A DIY Guide to Fixing a Broken Outside Faucet Pipe.

When you have a leaky outside faucet, it’s hard to enjoy the yard or garden. You might not know how to fix this issue yourself, but don’t worry! There are many DIY methods that you can use to fix this problem. All you need is some basic plumbing knowledge and supplies.

This guide will teach you how to fix the leaky outside faucet pipe. With these three methods: replacing the gasket, using PVC cement for a temporary fix, or replacing the brass insert in the pipe. Regardless of which method you choose, your outdoor faucet will be fixed in no time!


Outdoor Faucet Leak? There’s a Fix

If your outdoor faucet has developed a leak, don’t panic. You can easily fix it yourself with some basic plumbing knowledge and supplies. All you need is some basic plumbing knowledge and supplies. This guide will teach you how to fix the leaky outside faucet pipe. With these three methods: replacing the gasket, using PVC cement for a temporary fix, or replacing the brass insert in the pipe. Regardless of which method you choose, your outdoor faucet will be fixed in no time!


What You’ll Need:

  1. Phillips screwdriver
  2. rubber gasket, PVC cement, or brass insert
  3. wrench
  4. electrician’s knife or hacksaw
  5. cutting pliers or vice grips
  6. penetrating oil

DIY Methods To Fix Outdoor Faucet Pipe

Outdoor Faucet Repair from Freezing

Fixing a leaky outside faucet is often an easy DIY project for homeowners. The first step when you find water leaking from under your outdoor faucet is to identify where the leak is coming from. You can use a flashlight to peer into the pipe and see if there’s an obvious cause of the leak.

Once you’ve found the source of the leak, it helps to turn off the water supply to your house so that you don’t waste any more water.

There are three common DIY methods you can use to fix this issue: replacing the gasket, using PVC cement for a temporary fix, or replacing the brass insert in the pipe.

To replace the gasket, remove all dirt and debris from around the base of your spigot handle.

Remove any screws holding down your outside faucet handle with a screwdriver. Remove any springs with pliers. Pull old gasket out with needle-nose pliers. Put the new gasket in place and slowly reattach the handle until it clicks into place on each side then tighten each screw securely.

To seal it on properly, put on some silicone around the edges of the spigot assembly before reattaching the spigot handles.

If you want a temporary fix while waiting on new parts for your outside faucet, apply PVC cement to the pipe. Wait five minutes for the sealant to dry, then turn on the water supply at the spigot handle.


Replacing the Gasket

The most common reason for a leaky outside faucet pipe is a damaged gasket. This can be fixed by taking apart the faucet and replacing or tightening the gasket.

To get started, turn off the water supply to your outside faucet. Take apart your outdoor faucet at the base of it with a wrench and pliers. Remove the old gasket and replace it with a new one, or tighten up an existing one that needs it. You will then be able to put the faucet back together again.

If your faucet continues to leak, you may have to replace the gasket. This can be done by taking apart the faucet again and removing the old gasket. You will then be able to put the faucet back together again.


Using PVC Cement For a Temporary Fix

If you have a temporary fix, you can use PVC cement. You’ll need to cut the pipe off at the top of the leak and use PVC cement to seal it back on. Be careful not to get any cement on the threads of the pipe.

  1. Prepare for the repair by cutting off the pipe at a point above where it is leaking.
  2. Put on a pair of rubber gloves and coat PVC cement liberally over both ends of the pipe you cut off, as well as the section where it was connected to your existing faucet line. Let it dry for about five minutes so that it is set in place. Then, take apart your old faucet and remove its spigot handles and gasket. The PVC cement will be strong enough to keep everything together while you finish dismantling your old faucet, but not so strong that you can’t take it apart later.
  3. Use a wrench to remove the section of pipe you cut off, and take it to the hardware store to find a replacement. You will need to get another piece of pipe that is the same size and threading as the one you cut off, but it doesn’t have to be identical.
  4. When you get back home, put your faucet back together again and use a wrench to tighten everything up. Test your faucet for leaks by running water through it at full force for five minutes, then turn off the water supply and check for any additional leaks. If there are any small leaks, use some PVC cement on them as well.

Replacing the Brass Insert In the Pipe

  1. Use a wrench to remove the brass insert from the pipe, then take it to the hardware store to find a replacement. You will need to get another piece of pipe that is the same size and threading as the one you cut off, but it doesn’t have to be identical.
  2. When you get back home, put your faucet back together again and use a wrench to tighten everything up. Test your faucet for leaks by running water through it at full force for five minutes, then turn off the water supply and check for any additional leaks. If there are any small leaks, use some PVC cement on them as well.

Conclusion

With the tips from this article, you should now have a better idea of what you need to do to fix a broken outside faucet pipe. There are a variety of ways to fix a leaky pipe and a lot of them can be done by yourself. I hope you found the article helpful and that you now know how to fix a broken outside faucet pipe.